Dust Collection Accessories

Long Ranger III Remote Dust Collector Switch

Turn on your dust collector from anywhere in your shop with the NEW and Improved "Long Ranger II" Remote Dust Collector Switch.
Save yourself the inconvenience of walking over to turn on your dust collector when you find you're in the middle of a critical project. Simply press the transmitter on/off button to easily switch your dust collector on or off.

Advantages Of This Great New System Include:

• Simple, Reliable and
  foolproof operation
• 5 ft. cord on the receiver module.
• Heavy duty commercial quality construction.
• Convenient belt clip on transmitter
• Available in 110V and 220V versions
• F.C.C. approved
• Extra hand piece transmitters available.
• Multiple frequency codes
• Grounded w/reset button
• Uses R.F. signal, not affected by: Outside interference by large TV's, Transformers, electrical noise, or 3 Phase Power sources
• Transmitter need not be aimed directly at Receiver– can go through walls!
  

Jumbo Dust Pan

Heavy duty metal. Built to last a lifetime.

• 17" wide x 10" deep
  

Gortex Cleanstream Wet / Dry Vac Filters

CleanStream® wet/dry vac filters trap ultra fine dusts that the filters originally supplied with your vacuum cleaner miss. They easily replace paper cartridge filters and bag filters. CleanStream® wet/dry vac filter media collects 99.7% of all particles at 0.3 microns. Ordinary wet/dry vac filters capture less than 20% of these particles. CleanStream® Filters' exclusive nonstick surface resists clogging and sheds dirt easily...even caked-on dust.

Floor Dust Collector Stand

This "take it with you" dust collection nozzle attaches to your dust collector so you can quickly and easily get rid of dust at machines and work stations everywhere in the shop. The cast nozzle rotates a full 360 degrees and can be angled up to 180 degrees in any position from straight up to straight down. Locking stand adjusts up and down from 24" to 43-1/2". Nozzle measures 1-1/8" x 12-1/2" and has a 4" OD port opening. Steel stand and tubes.

Two Stage Dust Separator Lid

A two stage dust collection system protects your dust collector from larger debris and allows you to empty your dust bags less frequently. These separator lids let you convert an ordinary container to a component of a two stage system.

30 gallon dust separator lid for 4" hose

5 gallon dust separator lid for 2 1/2" hose with or with out
hose fitting #445

Trash Can Cyclone Lid

Improve your single stage dust collector’s efficiency by converting it into a 2-stage unit with this lid and a common trash can! The Cyclone Lid lets you collect the larger and heavier shavings and dust before they reach your impeller and dust collection bags. Attaches with 4" hose and hose clamps. Fits standard 30 gallon metal trash cans.

5 Gallon Dust Collection Separator. For use with shop vacs. Similar to above, but fits on a 5 gallon bucket .Attaches with 2 1/2 " hose and hose clamps. ABS plastic.

30 Trash Can Cyclone Lid for 4" hose

Dust Picker

Capture dust from nearly any anywhere with the Dust Picker. Attaches to a floor base, clamps to a table or mounts to a wall or ceiling. Arms extends 44" vertically and 60" horizontally. Pivoting and locking mechanisms allow the arm great mobility
and flexibility for easy positioning.
Plastic hood has 4" x 10" opening, accepts 4" hose.
(Hose not included.)

Dust Picker Positioning System (hose not included)

Table Saw Safety Dust Guard

This Table Saw Safely Dust Guard is the ideal solution for table saw safety and dust control. When connected to a dust collection system, the PSI Dust Collection Guard captures the dust thrown up by your table saw blade. The Guard can be used on any table saw with an extension table. It is very easy to install and easily swings out of the way. A unique counter-balance allows for fast & easy positioning.

Features and Specifications:

• Protects you from hazardous table saw debris
• Hood is constructed from one piece, clear shatterproof plastic
• Accepts saw blades up to 16 "
• Can use with dado blades• Allows tilts for 45degree cuts
• Adjusts easily to suit thickness of material being cut
• Accommodates splitter and anti-kickback pawls
• Connects to a standard 4" duct system
• Boom extends to a full 83"
• Can be mounted to ceiling for maximum clearance
• Easy setup and adjustment• Easily swings out of the way
• Sturdy steel mast and boom construction
• Connects to 4" dust hose